EDSVSS−9. 9ä. System Manual. (Extension). 75 kW l. EVSxS EVSxS. Servo inverter. Global Drive. The System Manual is the basis for the description of the vector frequency inverter. Together with the System Manual (extension), document number. The vector range of frequency inverters is also perfectly equipped to handle complex applications, such as deployments in dosing, filling and feedforward.
|Published (Last):||27 May 2018|
|PDF File Size:||16.54 Mb|
|ePub File Size:||7.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
Complain wrong Brand wrong Model non readable. In the case of absolute positioning, no homing llenze performed before the first positioning. Control drive in negative direction.
The angle difference between set and actual position is larger than the following error limit set under C Parameter set mode is absolute instead of relative. You could probably recreate the Helmhotz drivers by yourself, if you knew how the CAN module communicates with the CPU over the backplane, how the CAN module must be parametrized for CAN BUS and how toexchange betweenthe CAN module and the drive,, If you do not have the information, I strongly suggest you get purchase the Helmholts CAN parametrization software and the handling blocks for the S, so you can concentrate on your project making the drives do what you need them to do instead of finding ways to talk to the drives.
Find out why the value was exceeded e. The reference point is not known. Perform one of the following functions and restart: An absolute parameter set C was performed during relative positioning position mode C Temperature inside the controller Sensor for detecting the internal temperature indicates undefined values.
servo inverters – Lenze in Germany. As easy as that.
Error in positioning program. Increase following error limit under C If necessary, adapt the position limit values or check whether the program function “set position value” is to be applied. Control drive in positive direction. Troubleshooting and fault elimination, System error messages general error lenzw — Lenze 0.
Best regards CS Moderator. Error “actual reference dimension offset”. A parameter set with final speed must be followed by a parameter set with positioning; it is not permissible to wait for input. Follow us on Twitter Youtube.
During initialisation of the controller, an incorrect power stage was detected. Sensor for detecting the heatsink temperature indicates undefined values. Temperature inside the controller.
vector inverters – Lenze in Lithuania. As easy as that.
Error of the program function “set position value”. Handling blocks should be ordered from Helmholtz, look on page 96 of the document page 930 of Error “negative limit switch”. Site Explorer Site Explorer.
Error “positive limit switch”. Heatsink temperature sensor error.
Positive position limit C was exceeded. Find out why the value was not reached e. Perform one of the following functions and restart:. Negative limit switch was reached. New question published by Shahjee is split to a separate thread with the subject brake functions or Brakes will Automatically applied.
Internal fault power stage. Impermissible programming Check position program: If you do not have the information, I strongly suggest you get purchase the Helmholts CAN parametrization software and the handling blocks for the S, so you can concentrate on your project making the drives do what you need them to do instead of finding ways to talk to the drives.
Sensor for detecting the internal temperature indicates undefined values. Anything is possible, with enough ressourcesinformation and time. Hope this helps, Daniel Chartier. Change the parameter set from absolute to relative. Have a look at this document from Helmholtz, it gives an example on whatmust be set and how to so the CAN modules can read and write to a drive:.
Actual reference dimension offset C outside the position limits.
Troubleshooting and fault elimination. Hello aran; Anything is possible, with enough ressourcesinformation and time.
Positive limit switch was reached. Drive cannot follow the digital frequency I max limit.
Have a look at this document from Helmholtz, it gives an example on whatmust be set and how to so the CAN modules can read and write to a drive: Negative position limit C was not reached. Product Support Services Forum mySupport.
9300 PLC servo inverters
Drive cannot follow the digital frequency I. Error “positive position limit”. Error “negative position limit”. Start homing in the program.